Understanding Plumber's Essentials When Installing a Bathtub
Understanding Plumber's Essentials When Installing a Bathtub
Blog Article
The article author is making a few good annotation relating to How to Install a Bathtub Yourself as a whole in this great article down the page.
Mounting a bathtub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the task can move immediately; if you need to open up a wall surface to get rid of the old bathtub and position the brand-new tub, the job is much harder. In either situation, the project is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have certified yourself for the job and also are comfortable trying it. As opposed to employing a service provider to take control of a halfway-completed task, it is much better to take into consideration employing one before you start. Opportunities are you may require an expert plumber to make tube links.
This post will aid you set up a new tub in your restroom if you have actually currently acquired a brand-new tub and also don't need to transform the setup of your previous supply of water pipelines.
Your tools and also product list should consist of the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps unit to prevent stress on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the restricted access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly come from the pipes. Once the supply pipes have been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the tub in the called for position. The wooden boards are practical in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bath tub till the level reviews degree.
To install faucets, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water system as well as inspect all joints and new pipework for leakages and also tighten them if required. Fill the tub as well as also check the overflow outlet and the regular electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait until the bathtub has been utilized at the very least when as this will certainly resolve it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin making certain that the washing machines are in area in between the faucet and also the sink. Safeguard the faucet in place with the maker offered backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap ports. The former type needs to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, resulting in issues with dampness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealer can break relatively very early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very serious about Installing A Bathtub and I'm hoping you enjoyed reading the entire page. Enjoyed reading our blog entry? Please share it. Let somebody else find it. I love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Need fast plumbing resolution? Call. Report this page